HTC ‘SuperFloor’ by Quest is a flooring system designed to provide a long lasting, low maintenance and environmentally low impact floor surface. The process involves mechanically refining the concrete surface by removing the top layer and revealing the underlying, more durable layers so that we can grind or polish it to provide a matt or polished finish which will provide an easy to clean, environmentally friendly and hard wearing surface. This means it’s very suitable to areas that see high foot traffic and a lot of heavy machinery, such as industrial environments like warehouses or engineering facilities; but is also at home in retail, leisure and exhibition environments where an industrial feel might be desirable.
The concrete floor is cut with a variety of diamond abrasive grits, usually 3-8 depending on the gloss level desired. This polishing can be done wet or dry depending on the site situation. Benefits of dry grinding include easier clean-up since no slurry is created during the process.
A densifier is then applied once the concrete is opened up and in a condition to readily accept the chemical. The step at which the densifier is applied is determined by the person polishing the concrete. The densifier is allowed to dry and cure for the manufacturers recommended time, followed by one or more abrasive cuts, which will polish the floor to the desired gloss.
Have you got issues with poor existing floor joints? If so, FloorBridge® installed by Quest is the solution. FloorBridge® is a unique joint reinstatement system. Made from a visco-plastic carbon fibre composite, FloorBridge® can be ground flat to the level of the adjacent floor ensuring the smoothest and possible transition across the joint, ensuring the safety of operatives across the floor.
Proven to be more robust than many other jointing systems, with a longer lifetime for any vehicles expected on the surface; FloorBridge® is an economical and ecological solution to joint problems within your floor slabs. The system is also a long lasting addition to your floor joints that will increase the lifespan of the surface; making it a cheaper option than replacing the whole floor in the event of irreparable damage to the old joints.
Main advantages include:
An investment protected by a warranty of up to twenty years.
Reduce maintenance costs of MHE
Prevents loss and damage to stock
Helps to prevent back problems with drivers
Completely impact free
Prevents recurring damage to your floor joints
Reduced noise when trafficking the joint
Easy to keep clean
The system is easy to apply (approx. 12 hours) in all areas and environments without unnecessary disruption to production and operations; providing a perfect, everlasting solution for all kinds of joint problems within a busy industrial environment.
Fields of Application include:
Warehouse (including very narrow aisles warehouses)
Automotive and Manufacturing companies
Multi storey car-parks (including underground)
Medical sector (hospitals)
Pharmaceutical sector (production and distribution)
ComfortFloor® is more than just a sleek, stylish floor. It’s about how people see and respond to the cool look and the warm touch. Sika’s polyurethane liquid applied to floors offers a seamless result – to help realize the most modern creative concepts.
Quest specify ComfortFloor® as a flooring solution for many of our projects. Our partnership with Sika allows us to better integrate this great system into our operations and offer more effective options to our clients.
Find out more about Sika®-ComfortFloor® by clicking here!
A multi-national clothing retailer contacted Quest in regards to a flooring refurbishment project within one of their stores. They were specifically looking for an industrial aesthetic, but also a surface that was easy to clean, low maintenance and hard wearing as the flooring had to ensure the safety of the customers and employees working in the store.
After listening to the clients’ requirements and comments, Quest suggested grinding and polishing the already existing concrete surface within the store. This was considered by the client and after some discussion, it was approved, as it closely matched the flooring aesthetic of some of the clients’ other stores.
After approval, Quest quickly acquired the relevant machinery to site to carry out the work required to create the desired floor with minimal disruption to the daily operations with the premises; using both the grinding equipment and polishing machines Quest own in-house.
While the whole refurbishment programme was taking place, Quest provided both day and night shifts in order to help accelerate the work of the main contractor, who were completing other tasks within the store in tandem with the flooring work being carried out.
Overall, the chosen polished concrete finish was successfully created within the agreed project timescales. In addition, the standard of the work carried out was so high that the retailer client has returned to Quest to request tender for the same work on their other stores throughout the UK.
‘Comfort flooring’ or ‘liquid vinyl’ resin systems have been growing in popularity in recent years. These types of resin floors are generally a modified FeRFA Type 5 flow applied system, comprising a primer, a flow applied ‘body coat’, optional surface sealer and may include a rubber underlay and associated adhesive and pore filler. This type of resin flooring aims to offer the user the comfort properties typically provided by cushion vinyl, with the additional benefit of providing a seamless hygienic floor. Comfort flooring is monolithically bonded to the substrate and therefore removes the need for welded joints. Resin flooring can also be overlaid at the end of its life span unlike vinyl which needs to be removed and disposed of.
These type of systems generally obtain their resilient properties from the ‘body coat’, which is usually a flexible 2 – 4 mm flow applied two-part resin self-smoothing material, and often may incorporate a filler component to increase the overall thickness of the system. Some ‘body coats’ are inherently colour stable and may be given a clear coat for scratch resistance or left un-coated. . The non-colour stable grades are usually specified with a thin colour stable top-coat. A slip resistant topcoat is also an option. Comfort Flooring systems may have a shorter lifespan than other Type 5 systems due to the relatively low thickness of the topcoat. Systems incorporating a underlay mat require an adhesive to bond the mat to the substrate and a pore filler to grout any holes between rubber crumb particles. The body coat may be specified in two thinner applications (for example 1.5 mm each) to improve smoothness and reduce the risk of protruding rubber particles affecting the surface finish.
The rate at which electrostatic charge is dispersed within and through the floor finish is controlled by the resistance, measured in the unit Ohms (Ω), usually expressed in thousands (Kilo-ohms or KΩ) or millions (Mega-ohms MΩ) and denoted by units expressed as a figure of ten with indices, i.e.103 for 1KΩ or 106 for 1MΩ. Greater values of resistance suggest a slower passage of electrostatic charge and the decay of voltage measured.
Resistance may be measured in one or more of four ways:
(a) between two points at a pre-defined distance on the surface of the cured resin floor finish
(b) between the surface and the underside of the resin finish (the substrate)
(c) earth leakage of the whole system, between the surface of the resin finish and via the substrate to a point defined as electrical earth
(d) a combined body voltage test where the charge level generated and its decay rate on a person walking the floor is measured using specialist equipment to identify the interaction between floor and specialist footwear.
It is not uncommon for those operating facilities which demand static controlled flooring to be unsure of their exact numerical requirements, when expressed in the terms above.
Static controlled grades of resin flooring are available in Types 3 to 8 (coatings, self-smoothing and trowel applied screeds). It is important for the specifier to understand that there is a wide range of products and properties available and to select the system that best meets the requirements for the working environment as a whole and to not treat the individual elements in isolation. Colour should be discussed with the flooring manufacturer, as there may be certain colour limitations on static controlled flooring due to the darkening effect of carbon or other conducting additives.
An office fit out contractor contacted Quest in regards to a flooring project that involved installing a concrete topping onto several different areas within an office premises – this included one flight of stairs, seven lift lobbies/landings and adjacent corridors; totalling 130m2 of flooring.
The client wanted a surface that was easy to clean and low maintenance but also non-slip as the flooring had to ensure the safety of the employees and visitors to the building. After listening to the clients’ requirements, Quest made the decision that a concrete topping was the most viable option and a tender for the works was provided as appropriate.
Quest were awarded the contract shortly after the tender was provided and a programme was set out in order to properly timetable the work to be carried out. Quest were given 2.5 weeks on the site from the start of the project in order to complete the job. Before arrival, Quest carried out preparations to get all the materials at the correct time as the site was incredibly busy throughout the entire project.
The materials arrived on time and were batched for the entire job. This included the necessary equipment needed for the substrates preparation, which was all carried out by Quest within the time period detailed in the programme.
Despite challenging conditions and a very busy site environment, Quest completed the project in only 2 weeks and handed over the installation ½ a week ahead in line with the main contractors programme and to the end users satisfaction.
Quest were contacted by a main contractor and asked to tender for works on a public sector project within a college facility. This included installation of a resin flooring based system for an engineering workshop.
After initial contact, Quest put forward a tender and the order was accepted 4 weeks ahead of the programmed start date, which allowed for thorough planning to take place in order to ascertain the best flooring solution for the environment the end user specified to the main contractor. Altrotect Plus was specified by Quest as the best solution for the mechanical engineering space incorporating a 3 part system (one part DPM primer and two parts resin coating) which would provide a surface in line with the end users specifications.
Quest then met with the client to present the selected system to explain that it would provide a hard wearing, easy to clean and long lasting surface that would reflect the lighting in the space to give a much brighter feel to the environment. This was met with approval by the client and the system was approved for the project.
The entire project was programmed for one week but Quest finished in just 5 days; with all materials for the 1000m2 floor delivered at once from a single production in order to ensure no shade variations in the surface.
Both the main contractor and end user were very happy with the results of the final installation, due in large part to the work being completed ahead of programmed time and on budget and the floor is now used by the engineers of the future in the college today!